NEWS

You want to know more about the crusher knowledge, technology, news,Cone Crusher news,jaw crusher news,sand making machine news,We offer you free line configuration。

Maintenance and maintenance of stone crushing production line in the production process

Author:Xinhai     Time:2021-08-16 16:52:47

If you need our products,you can leave your contact informaction,our sales manager will send more information and quotation to you! Our email: sales@zxcrusher.com, WeChat/whatsapp:+8613676922906.

Everyone knows that the equipment of the stone crushing production line is gener y operated in the open air, exposed to wind and rain, and the working environment is very harsh, and when working for a long time, the working strength of each part of the equipment is relatively high, and problems such as wear and breakage are more likely to occur. If the basic maintenance and maintenance cannot be done well, then the production cost is very large. Therefore, in the process of using the stone crushing production line equipment, it be regularly maintained. Although it cannot prevent the aging of the machine, it can extend the service life of the machine to a certain extent and maintain stable and efficiency. The specific basic maintenance and maintenance methods are as follows: Stone crushing production line

1, Must start without load
When the stone crushing production line equipment is started, if there is material in the crushing cavity, the motor will be burned out due to the excessive starting pressure of the motor, and the miracle will also be damaged in other aspects. Therefore, you pay attention to clean up the debris in the crushing cavity before starting to ensure no-load start. Be sure to start *, and then add ore materials to it.

2, The nature and characteristics of the material are within the specified range
Any stone crushing production line equipment has its scope of application, and equipment of different specifications has different requirements for the feed size, hardness, humidity, etc. of the material. When the hardness, lumpiness, humidity, etc. of the materials are out of the equipment's tolerance range, conditions such as blockage and abrasion will occur, and the damage to the equipment of the stone crushing production line is very serious. Therefore, the selection of materials match the specifications of the equipment.

3, Regularly repair and replace easy-to-wear parts
Regularly shut down and open the observation door to observe the internal wear of the impact stone crushing production line equipment, the wear level of the center feed pipe, cone cap, impeller upper and lower runner linings, circumferential guard plates, and wear blocks. After wear, they should be replaced or repaired in time. , When replacing the wear blocks, they should be replaced at the same time to ensure that the weight of the wear blocks is the same. If the impeller body is found to be worn, replace it in time and seek repair from the manufacturer. In , it is strictly forbidden to make impellers without the consent of the manufacturer.

4,Do a good job of lubricating the equipment of the stone crushing production line
The equipment of the stone crushing production line can only operate norm y and stably when the lubrication is good. When the lubrication is insufficient, the wear of the machine will increase and the bearing will heat up, which will damage the machine. Therefore, the stone crushing production line equipment should be checked for lubricating oil after a period of use. The machine reminds users: the gravel crushing production line equipment should be added with grease after 400 hours of operation, and the bearings be cleaned after 2000 hours of operation. If the work reaches 7200 hours, new bearings be replaced. Only in this way can the machine last long.

5, Fasten loose parts in time
The equipment of the stone crushing production line is fixed together by screws and other components, and these screws will loosen if they are exercised frequently. If abnormal noise occurs during use, s* the machine in time for inspection. Loose parts are found and fastened in time.

6, Shut down and rest regularly
The equipment of the stone crushing production line is the same as that of people. After working for a long time, you need to rest. In order to pursue high production, let the equipment run day and night, which will inevitably accelerate its damage. Therefore, according to the strength of the crushed materials, letting the equipment work for a period of time to s* and adjust and rest is a very necessary point in the basic maintenance and maintenance of the stone crushing production line equipment.

Related MaterialsMORE+

Related CaseMORE+

Contact Form

Email: sales@zxcrusher.com, Phone: 0086-371-67660555, Whatsapp/Wechat:+86-13676922906, Skype:zxcrushers@outlook.com
Please feel free to give your inquiry in the form below. We will reply you in 24 hours

Your Name:
*E-mail:
Your Tel:
Country:
Capacity(t/h):
Instant Messenger:
Message:
Copyright:JIAOZUO CITY XINHAI MINE MACHINERY EQUIPMENT PLANT(GENERAL PARTNERSHIP) XML HTML