0086-371-67660555/+86-13676922906

Your Location:Home > News  > Analysis of the reasons for the decrease in the output of sand making machine equipment

Analysis of the reasons for the decrease in the output of sand making machine equipment

As the main crushing equipment in the sand production line, sand making machine equipment has a very large loss. Many customers have questions about the wear problem of the sand making machine. The quality problem of the sand making machine is suspected, and some are due to the use of the sand making machine. Caused by improper use in the process. Only by paying attention to the maintenance and maintenance of the sand making machine can the sand making machine be fully functional and prolong the service life of the sand making machine equipment.

  The bearings of the sand making machine equipment are easy to wear, and the parts bear * of the load during the operation of the equipment. Therefore, we must use good lubricants during work and keep them clean at all times. If the lubricant is not clean, it will increase the wear between the bearings, the bearings and other parts. In addition, pay attention not to overheat the bearing. Overheating will reduce the operating efficiency of the bearing and affect the normal operation of the equipment. The transmission device and the V-belt of the sand making machine equipment should be properly adjusted to ensure that the V-belt is evenly stressed. When driven by dual motors, it should be distributed reasonably and the strength is the same. The maintenance of transmission gears and long-term frictional wear between transmission gears will also affect the life of the machine. Corresponding to the lubricant used to solve the bearing problem is also an important one.

  The stability of the traditional sand making machine is not as good as that of the new sand making machine, and the maintenance rate is higher. But the price of traditional sand making machine is relatively cheap. But no matter in terms of product performance or cost-effectiveness, more people are willing to choose new sand making machines. It can increase the output better than the traditional sand making machine, and at the same time reduce the environmental pollution.

  In the process of small sand making machines, various problems will occur, and vibration is also one of the common problems for users. This is also a common phenomenon because vibration occurs during long hours of work. If it vibrates for a long time, it will cause screws. One of the reasons for regular inspection and maintenance of small sand making machines is that the parts are loose or even fall off. Hydraulic vibration isolation. The hydraulic support system is a combination of traditional rubber support and hydraulic damping. It can provide large damping in the low frequency range and quickly attenuate large-value engine vibration. It has low dynamic stiffness and energy at intermediate and high frequencies. Effectively reduce the vibration and noise in the cab.

  Of course, there is not only a sand making machine on a complete production line, but also many equipments, such as jaw crushers, cone crushers, vibrating screens, conveyors, etc. The selection of these large-scale equipment is based on the solution of the whole process and its own actual needs. Not all production lines need to be equipped with a new type of sand making machine. If the requirements for the finished product are not high, the production line only needs to be crushed once and twice, and if the requirements for the finished product are high, a new type of sand making machine is recommended.



Inquiry >> Please feel free to give your inquiry in the form below. We will reply you in 24 hours.
Your Name :
E-mail: *
Your Tel : (We Suggest You Tell Us Your Telephone Number Which Will Contribute To Our Communication)
Your Country :
Instant Messenger:
Message:

news

  • What is the price of the entire sand production line?1.What is the price of the entire sand production line?
  • What should the mobile stone crusher be used for the first time?2.What should the mobile stone crusher be used for the first time?
  • Brief introduction of the impact crusher maintenance3.Brief introduction of the impact crusher maintenance
  • What is the difference between VSI impact crusher and impact crusher?4.What is the difference between VSI impact crusher and impact crusher?
  • How to Choose the Jaw Crushing Plant?5.How to Choose the Jaw Crushing Plant?
  • Case

    1000TPH Mountain Stone Crushing Plant In Sri Lanka1000TPH Mountain Stone Crushing Plant In Sri Lanka 300TPH Mountain Stone Crushing Plant In Indonesia300TPH Mountain Stone Crushing Plant In Indonesia 200T/H Aggregate Stone Crushing Plant In Philippines200T/H Aggregate Stone Crushing Plant In Philippines Configuration of 250TPH River Stone Crushing PlantConfiguration of 250TPH River Stone Crushing Plant